Every pet hair job includes the full source-removal process on the supply and return sides, the plenum, and the coil. Sanitizing, dryer vent cleaning, and filter upgrades are add-ons you can decide on after the inspection. Here is what you get as standard.
Every branch run on both sides of the system, cleaned with rotary brush and air whip under negative air. Not just the visible vents. We work from the farthest register back to the plenum so nothing gets pushed into a clean section.
The plenum and main trunk hold the heaviest fur mat in a Murphy home. We open an access panel, agitate the walls, and vacuum the floor of the plenum with a HEPA vacuum. This is the single most important step on a pet hair job.
We clean the coil with coil cleaner and a soft brush, and wipe down the blower wheel. A fur-loaded blower wheel runs out of balance and gets loud. Cleaning it restores quiet operation and proper airflow.
Before and after footage of your trunk and at least two branch runs, shown to you on site. If you want a copy for insurance, a home sale, or your allergist, we can send the files.
We re-seal every access point with mastic and duct sealant and replace torn duct insulation we find during the job. Loose insulation is where fur and dust collect first, so sealing it properly matters.
We check your filter size and MERV rating against what your system can actually handle, and we check static pressure before and after. In heavy-pet homes, the wrong filter chokes airflow worse than the fur did.
Air duct cleaning for pet hair in Murphy is a source-removal process that pulls accumulated fur, dander, and the dust that binds them out of your supply and return ductwork, then captures it in a HEPA vacuum instead of blowing it back into your rooms. Pet hair behaves differently than ordinary house dust. It is long, it tangles, and it catches on every seam, screw head, and turning vane inside a flexible duct run. Once it mats down on the return side, it acts like a filter that keeps getting denser, which chokes airflow and drives up static pressure on your blower.
Murphy homes tend to run two or three pets, and most were built with flexible duct in the attic. That combination is the worst case for fur accumulation. Add the Collin County pollen load from March through October and you get a duct system that is holding fur, dander, pollen, and dust all at once. If you have been searching for air duct cleaning for pet hair Murphy TX near me and getting nothing but vent-vacuum outfits, the difference matters: we clean the whole run, not just the register.
Five steps, one visit, usually two to four hours for a standard Murphy house. Here is exactly what happens from the moment we pull into your driveway.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Negative air machine with HEPA filtration
Puts the entire duct system under vacuum so loosened fur and dander travel to the filter instead of into your living space. We use Abatement Technologies units on every job.
Rotary brush and air whip
The rotary brush breaks the fur mat off the duct wall; the air whip scours corners and seams a brush cannot reach. We run lower RPM on flexible duct to protect the inner liner.
Duct camera
Documents the condition of the trunk and branch runs before and after cleaning. You watch the screen with us, so the result is verified rather than claimed.
HEPA vacuum
Used on the plenum floor, blower compartment, and register boots, where a negative air machine alone does not reach. Captures particles down to 0.3 microns.
Compressed air nozzle
Cleans the blower wheel fins and the tight areas around the coil casing where fur packs in and a brush will not fit.
Duct fogger
Applies an EPA-registered sanitizing product through the system when there is an odor or microbial issue. An add-on, used only when there is a reason.
Rotobrush and Nikro equipment
Our primary agitation and vacuum platforms. Rotobrush handles the branch runs; Nikro units cover the larger trunk and plenum volumes.
NADCA source-removal standard
The NADCA approach puts the system under negative pressure, agitates every surface mechanically, and captures the debris at the source. It is the difference between cleaning a duct and wiping a vent. Every pet hair job we run follows this sequence.
Push-pull agitation
We work each branch run from the farthest register back toward the plenum, so debris moves in one direction and never crosses a section we already cleaned. On long Murphy attic runs this prevents re-contamination of the first half of the duct.
Static pressure verification
We measure static pressure at the air handler before and after cleaning. It is the objective number that tells you whether the fur restriction is actually gone, and it is the number that correlates with your energy bill.
IICRC post-remediation verification
After cleaning we run the camera back down at least two runs and confirm bare duct wall. If we see remaining buildup, we go back and re-agitate that section before we pack up.
01
What we do: We run a camera inspection first to see how much fur is left in the system, then clean the full supply and return, the plenum, and the coil. We also check the filter frame for gaps and replace torn insulation.
→ You start fresh in a house that smells and breathes like yours, not like the previous owner's pets.
02
What we do: A full cleaning now removes the seasonal load before it mats down further. We time the visit so the system is clean going into the heavy AC months, and we set you up with the right filter for the next shed cycle.
→ Lower dust through the summer and a return line that is not already packed by the time fall arrives.
03
What we do: We do the full source-removal cleaning, clean the coil, and fog the system if the allergist recommends it. We also give you specific filter guidance based on what your blower can handle without losing airflow.
→ A measurable drop in airborne dander, plus a maintenance schedule so the reservoir does not rebuild.
04
What we do: We clean the system and provide before-and-after camera footage plus a written summary you can hand to the buyer's agent. If they want an independent inspection, we can arrange a NADCA Certified Ventilation Inspector.
→ A documented cleaning that closes the inspection objection and gets the sale moving.
05
What we do: We measure static pressure, inspect the return trunk for fur blockage, and check for collapsed or torn flexible duct in the attic. Then we clean and, where needed, repair the duct run.
→ Stronger airflow at the registers and a blower that runs quieter because it is not fighting a restriction.
Murphy sits in Collin County, and the housing stock here splits into two clear groups. The older neighborhoods near Downtown Murphy and Murphy Village have sheet metal trunk lines with shorter branch runs, which hold fur differently than modern duct. The newer builds in The Reserve, Stonebridge, and Creekside are almost entirely flexible duct in a hot attic, and that is where pet hair causes the most trouble. Flex duct has a ribbed inner liner, and every rib catches fur. Over two or three years it mats into a felt-like layer that reduces the effective diameter of the run. Add North Texas summers, where attic temperatures push past 140 degrees and the AC runs nearly continuously from May through September, and that restriction costs you real money. We also see the pollen load from March through October binding into the fur mat, which is why a pet dander duct cleaning Murphy 75094 job often pulls out more pollen than the customer expected. If you have been looking for air duct cleaning for pet hair 24/7 Murphy TX availability during a heat wave, call us, because that is exactly when a restricted return causes the most strain on your system.
Downtown Murphy
Older homes with sheet metal trunk lines and shorter branch runs. Fur collects at the seams and turning vanes rather than along the duct wall.
Maxwell Creek
Mix of flex and sheet metal, with several homes that have had attic duct repairs. We check for torn insulation on every visit here.
The Reserve
Newer construction with all-flex duct systems. These catch fur fast because of the ribbed liner, and most need their first cleaning at the three-year mark.
Stonebridge
Larger homes with longer trunk runs and multiple returns. The return plenum is usually where the heaviest fur mat sits.
Timber Creek
Established neighborhood with mature trees, so pollen load is higher and binds into the pet hair mat faster than in newer developments.
Attic temperatures above 140 degrees in summer
Heat bakes the fur mat onto the duct wall and makes it harder to break loose. We use longer agitation passes on summer jobs in Murphy attics to get the same result.
Heavy spring and fall shed cycles
Murphy homes with double-coated breeds see two large fur dumps per year. Booking a cleaning right after the spring shed removes the load before the AC season starts.
Collin County pollen season, March through October
Pollen binds into the fur mat and adds to the allergen load. A pet hair cleaning here pulls out pollen as well as dander, which is why allergy clients notice a bigger difference.
Flexible duct in nearly all post-2005 builds
The ribbed liner catches fur far more aggressively than sheet metal. We run lower-RPM agitation on flex so we clean it without damaging the inner liner.
These are the five calls we get most often from Murphy pet owners. If any of them sound familiar, the duct system is the place to start.
Problem
That grille is the last thing the air passes before the blower. If you can see fur there, the trunk behind it is packed, and your blower is pulling against a restriction every cycle.
Our Fix
We pull the grille, run the camera down the return trunk, and clean the full run under negative air. In most Murphy homes the return side holds three to five times the debris of the supply side, so we spend most of the job there.
Problem
Fine dander bound to hair fragments re-circulates every time the system runs. It coats surfaces, lands in bedding, and keeps allergy symptoms going even when the house looks clean.
Our Fix
Source removal plus a HEPA vacuum on the plenum floor cuts the re-circulation loop. We also check whether your filter is seated properly, because a gap at the filter frame lets unfiltered air bypass the media entirely.
Problem
Fur holds moisture against the coil and duct insulation. That is where microbial growth starts, and once it is established the smell comes back every cooling season until the source is removed.
Our Fix
We clean the coil and plenum, treat the affected sections, and if needed use a duct fogger with an EPA-registered product. We also look for the moisture source, because cleaning without fixing the leak means the problem returns.
Problem
A restricted return raises static pressure and forces the blower to work harder for the same airflow. That shows up as longer run times and a higher kWh number on your bill each month.
Our Fix
We measure static pressure before and after the cleaning. Most pet hair jobs in Murphy drop static pressure by 0.1 to 0.3 inches of water column, which is enough to shorten run times noticeably.
Problem
If someone in the house reacts to pet dander, cleaning the floors and washing bedding only goes so far while the duct system keeps re-seeding the air with the same protein.
Our Fix
A full pet dander duct cleaning in Murphy Texas removes the reservoir. We pair it with filter guidance and, where the allergist recommends it, sanitizing. Most families notice a difference within two to three weeks.
Pet hair in ductwork is not a cosmetic problem. It changes how your system moves air, what your family breathes, and how hard your equipment works. These are the four outcomes Murphy homeowners notice first after we finish.
Noticeably less dust on surfaces
A matted return line sheds fine dander every time the blower kicks on. Once we pull the mat out and HEPA-vacuum the branch runs, most customers tell us their furniture stays clean two to three times longer. That is the single most common comment we get on pet hair duct cleaning Murphy jobs.
Lower static pressure, easier airflow
Fur buildup on a return trunk can add 0.1 to 0.3 inches of water column to your system's static pressure. That is real money on your electric bill and real wear on your blower motor. Clearing the runs lets the equipment move the CFM it was designed for.
Fewer allergy flare-ups at home
Pet dander is the protein that triggers most reactions, and it rides on the hair. Removing both from the duct system reduces what gets re-circulated every cycle. Families dealing with air duct cleaning for allergies Murphy issues usually find the pet hair is the hidden half of the problem.
Musty odor gone from the vents
When fur traps moisture in an attic duct run, you get microbial growth on the duct insulation and a smell every time the AC starts. We treat the affected sections and, where needed, fog the system so the odor source is gone rather than masked.
Google ★★★★★4.9
Showed up on time, ran the camera, and showed me exactly what was in the ducts before they started. Two dogs and a house full of fur. The return trunk was worse than I expected. Cleaned it all out and showed me the after footage. No upsell, no pressure.
Yelp ★★★★★4.8
Called about a musty smell and they came out the next day. Turned out to be pet hair holding moisture on the coil. They cleaned the coil, the plenum, and the blower wheel, and the smell was gone. Fair price and they explained everything without talking down to me.
BBB ★★★★★4.9
We have three cats and I have allergies. They cleaned the whole system, fogged it, and gave me filter recommendations based on what my system could handle. Six weeks later I am sleeping better. Would use them again.
Google ★★★★★5.0
Quoted a flat price on the phone and that was exactly what I paid. They sealed up a torn section of duct insulation I did not know about and did not charge extra for it. Solid work.
PureBreeze Path has been cleaning duct systems in Murphy and the surrounding Collin County neighborhoods since 2022. In that time we have worked on everything from 1980s sheet metal trunks in Downtown Murphy to brand-new flexible duct runs in The Reserve. Our technicians train to NADCA Air Systems Cleaning Specialist standards, and we hold EPA Lead-Safe Certification and OSHA 10 cards. We carry a Texas HVAC License and follow IICRC guidance on source removal. Pet hair jobs are a specialty, not a side service, because the technique is different from a standard dust cleaning.
Real answers to the questions we hear most often from local homeowners and property managers.
Standard local air duct cleaning across Murphy covers the same source-removal process we use on pet hair jobs, minus the extra agitation passes. If your ducts are dusty but not matted with fur, this is the right scope and it costs less.
View local Airduct cleaningWhen you search air duct cleaning near me in Murphy, you want a company that actually works this ZIP, not a franchise dispatching from Dallas. We are based in Collin County and we know the housing stock here.
View Airduct cleaning near meOur 24/7 line handles the emergencies: a duct run that flooded after a storm, a system blowing musty air at 2 a.m., or a rental property that needs cleaning before a tenant moves in. Call (855) 948-0345 any hour.
View 24/7 Airduct cleaningSame-day air duct cleaning for pet hair Murphy appointments open up most weeks, especially in the spring and fall. Call before noon and we can often have a crew at your door the same afternoon.
View Same Day Airduct cleaningEmergency air duct cleaning is for water intrusion, smoke odor, or a rodent infestation in the ductwork. Those jobs need immediate attention because mold can start in 24 to 48 hours in a Murphy attic.
View Emergency Airduct cleaningCommercial duct cleaning for Murphy offices, vet clinics, and grooming shops, where pet hair and dander loads are far higher than a home. We schedule after-hours so we do not disrupt your business.
View commercial Airduct cleaningCall (855) 948-0345 or email info@purebreezepath.com and we will get back to you fast. Our phones are answered 24/7 for emergencies, and regular scheduling runs Monday through Friday, 8 a.m. to 6 p.m. If you are in Murphy, we can usually get a tech to your door the same day.
Phone
(855) 948-0345Address
410 W Farm to Market 544, Suite 102 Murphy, TX 75094 USA, Murphy, Texas
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
