Every dirty air ducts cleaning quote covers the full interior scope: all supply and return runs, the trunk lines, and the air handler components. Add-ons like sanitizing, dryer vent cleaning, and mold treatment are quoted separately so you can see exactly what each one costs before you approve it.
A duct camera pass through the main trunk and sample branch lines, plus a look at the evaporator coil and blower compartment. You see the screen, and the footage decides the scope. This runs about 20 minutes and it is included in every quote.
We seal all registers and tie an Abatement Technologies HEPA unit into the trunk so the ductwork stays under vacuum for the whole job. This is the step that keeps loosened debris out of your living space, and it is not optional on our jobs.
Each branch line gets mechanically agitated with a rotary brush sized to the duct, then an air whip for corners and transitions. Flexible duct gets a softer head so the inner liner stays intact. Every run is worked individually, not skipped.
The evaporator coil, blower wheel, and drain pan get cleaned with coil cleaner and rinsed so condensate drains clear. A fouled blower wheel can cut airflow by a third, so leaving it dirty would undo most of the benefit of clean ducts.
We re-run the camera on the same lines we inspected at the start and walk you through the footage. Registers go back on, the system runs for 10 minutes, and we confirm airflow at the furthest register before we leave.
Dirty air ducts cleaning Murphy TX is the mechanical removal of dust, dander, pollen, and microbial growth from the supply and return runs of your HVAC system. It is not a spray-and-hope job. We cut the system at the plenum, run a negative air machine to hold the ductwork under vacuum, then work each branch line with a rotary brush and an air whip. A duct camera confirms what came out and what is left behind.
Murphy sits in Collin County, where hot, humid summers push your system hard from May through September, and that constant cycling pulls dust and moisture into the ductwork. Add the spring pollen load and the pet dander from a house full of dogs, and flexible duct in older builds around Murphy Farms and Southgate collects a visible film within a couple of seasons. That film is what you smell when the air first comes on.
Every job follows the same five steps, whether it is a 1,800-square-foot house near Heritage Park or a 4,000-square-foot build in The Reserve. Most homes take three to four hours from arrival to walkthrough.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Abatement Technologies HEPA vacuum
The primary collection unit on every job. It holds the ductwork under negative pressure and captures fine particulate down to 0.3 microns, which is what keeps debris out of your living space during cleaning.
Rotobrush rotary brush system
Used on sheet metal and rigid duct runs to break the bonded film off the duct walls. Brush heads are sized to the duct diameter so the full circumference gets contact without damaging seams.
Air-Care air whip
Reaches corners, transitions, and the last few feet of a run that a brush cannot fully contact. It is the step that catches the debris sitting in elbows and takeoffs where buildup is heaviest.
Duct camera
Used before and after every job. It documents the condition of the trunk and branch lines, confirms the cleaning worked, and gives you footage you can actually look at rather than taking our word for it.
Nikro compressed air nozzle
Clears the blower wheel, coil fins, and cabinet surfaces inside the air handler. These components collect the same film as the ducts, and leaving them dirty undoes most of the airflow gain.
Duct fogger
Applies an EPA-registered sanitizer as a fine mist through the ductwork after mechanical cleaning. It is an add-on step, and we only use it where treatment is warranted and approved.
NADCA assessment, cleaning, and verification sequence
We follow the NADCA standard in order: assess with a camera, clean mechanically under negative pressure, then verify with a second camera pass. Skipping the verification step is how a lot of companies get away with a partial job. We document both passes on every Murphy property.
Source removal rather than chemical masking
The buildup has to come out of the ductwork physically before any sanitizer makes sense. We brush and whip first, vacuum the debris into a HEPA unit, and only then consider treatment. Sanitizing a duct that still has a film on the walls just seals the dirt in place.
Component-level cleaning
Ducts are only part of the system. The evaporator coil, blower wheel, and drain pan get cleaned on every job because they collect the same debris. A clean duct network feeding a fouled coil still runs hot and still smells.
Airflow verification at the furthest register
After cleaning, we measure airflow at the register furthest from the air handler. If it has not improved, something else is restricting the system, and we tell you what we found instead of calling the job done.
01
What we do: We run the camera first, because older sheet metal trunks in this part of Murphy often have joint gaps that let attic dust in. We clean every run, seal accessible joints with mastic and duct sealant, and verify airflow at the furthest register.
→ The new owners start with a clean system instead of inheriting 25 years of buildup, and the sealed joints keep attic dust out going forward.
02
What we do: Post construction duct cleaning is the right call here. We seal the registers, run negative pressure, and work each branch line with a brush and whip to clear the fine gypsum dust before the system runs a full cycle.
→ The coil stays clean instead of getting coated in the first month, and the family moves in without a dust haze every time the AC starts.
03
What we do: We inspect the bedroom branch lines and the return closest to the air handler, then clean the full system including the blower wheel. We also check the filter size and MERV rating to make sure it is not restricting airflow.
→ The overnight particulate load drops noticeably, and most customers report the morning congestion easing within the first two weeks.
04
What we do: That is a clogged dryer vent, not a failing appliance. We clean the vent run and check the exterior termination for proper clearance and a working backdraft damper, then confirm airflow at the outlet.
→ Drying time drops back to a single cycle, and the fire risk from packed lint in the vent run is removed.
Murphy sits in Collin County with a climate that is hard on ductwork: humid summers that push systems to run nearly continuously from May through September, and spring pollen loads that pull straight into the return. That combination means flexible duct in older builds around Murphy Farms and Southgate tends to collect a visible film within two seasons, while newer variable-speed systems in Stonebridge and The Reserve load up more slowly because they move less air at lower speeds. Homes along the Parker Road Corridor pick up extra particulate from traffic, and we see that in the camera footage as a darker film on the return side. Most Murphy houses have 12 to 20 supply and return runs, and a full cleaning takes three to four hours. If you are searching filthy duct cleaning Murphy 75094, we are already on routes through the 75094 ZIP code most weekdays and can usually get an inspection on the calendar within a few days.
Murphy Village
Older sheet metal trunk lines with joint gaps that let attic dust into the system. We check these joints on every visit and seal accessible ones with mastic and duct sealant.
Timber Creek
Mix of original flex and retrofitted rigid runs. The flex sections need a softer whip head so the inner liner does not tear during agitation.
The Reserve
Newer construction with variable-speed equipment. These systems move less air at lower speeds, so buildup is slower but coil cleaning still matters at the three-to-five-year mark.
Maxwell Creek
Larger two-story layouts with long branch runs to upstairs bedrooms. Those runs are the ones most likely to show restricted airflow and get checked first on the camera pass.
Southgate
Homes with dryers venting through longer runs, which makes clogged dryer vents a common find during the same visit as duct cleaning.
Humid North Texas summers with near-continuous system cycling
Constant runtime pulls more dust and moisture into the ductwork, and it accelerates surface growth on the evaporator coil. This is why we inspect the coil pan on every Murphy job, not just the ducts.
Heavy spring pollen load across Collin County
Pollen enters through the return and binds to duct walls, then re-circulates every cycle. Homes that run standard filters instead of HEPA filters see this buildup faster and need cleaning on the shorter end of the interval.
Attic duct runs in unconditioned space
Duct runs in a Texas attic see temperature swings that cause condensation on the exterior and, in poorly sealed systems, on the interior. We check these runs for moisture and insulation damage on every inspection.
Newer construction dust from ongoing development
Active building in and around Murphy means fine construction particulate in the air. Homes near active sites load their filters faster and benefit from post construction duct cleaning after any nearby remodel.
Most calls we get in Murphy trace back to one of four issues. Each one has a different fix, and the camera inspection tells us which one you are dealing with before we quote anything.
Problem
Dust settles on furniture, ceiling fans, and electronics within days of cleaning, and the HVAC filter loads up faster than it should. Over time the blower has to work harder to move the same air.
Our Fix
We remove the film from the duct walls with a rotary brush and air whip under negative pressure, so the debris goes into the HEPA vacuum instead of back into the room. Most customers see a clear difference within the first week of normal system cycling.
Problem
That damp smell usually means microbial growth on the evaporator coil or in a duct run near unconditioned space. Left alone, it spreads through the system and gets noticeably worse each cooling season.
Our Fix
We inspect the coil pan and any duct runs in attic space, clean the affected surfaces, and treat with a duct fogger using an EPA-registered product. If the growth is heavy, we quote mold in air ducts cleaning as a separate line item before starting.
Problem
Pet dander and pollen settle into the duct walls and get pushed back into bedrooms every cycle. Medication helps, but the reservoir keeps refilling the air all night long.
Our Fix
We remove the dander and pollen load from the ductwork and the blower wheel, then confirm airflow at the furthest register. Pairing this with a fresh HEPA filter and a 60-to-90-day change schedule is what keeps symptoms down long term.
Problem
A restricted return or a fouled blower wheel makes the system run longer to hit setpoint. In a Texas summer, that shows up as a 10 to 20 percent jump on the cooling portion of your electric bill.
Our Fix
We clean the runs, the blower wheel, and the coil in one visit, which restores the airflow the system was designed for. Customers in Creekside and Willow Wood commonly report a 5 to 12 percent drop on summer cooling costs after the job.
Clean ductwork changes three things you can measure: how much dust lands on your shelves, how the house smells, and how hard the blower has to work. Here is what customers notice first.
Less dust on every surface
When the supply runs are coated, every cycle re-deposits that film onto your furniture, ceiling fans, and window sills. After a full cleaning, most Murphy customers tell us they dust every 10 to 14 days instead of every 3 or 4. That is the single fastest sign the job worked.
Fewer allergy flare-ups
Pet dander and pollen settle in the duct walls and get pushed back into bedrooms all night. If someone in the house wakes up congested every morning, air duct cleaning for allergies is usually the first thing worth trying. We pull the reservoir out rather than masking it with a fragrance.
Lower energy bills from dirty ducts
A restricted return makes the blower work harder to move the same cubic feet per minute. Clearing the runs restores airflow, and the system reaches setpoint faster. Customers in Maxwell Creek and Timber Creek commonly report a 5 to 12 percent drop on summer cooling costs after cleaning and a fresh filter.
No more musty odors
That damp, sour smell when the AC starts is usually mold growth in ductwork or on the evaporator coil. We inspect the coil, treat the affected runs with a duct fogger, and confirm with a camera pass. If the growth is heavy, we quote mold in air ducts cleaning as a separate step so you know exactly what you are paying for.
Google ★★★★★4.9
Showed up on time, walked me through the camera footage before and after, and did not try to sell me anything I did not need. The upstairs bedrooms smell completely different now. Worth every dollar and I will use them again in three years.
Yelp ★★★★★4.8
Called about a musty smell and they had a tech out the same afternoon. Found the issue on the coil pan, quoted the mold treatment before starting, and finished the same day. No surprise charges on the invoice.
BBB ★★★★★5.0
We manage commercial suites and needed documentation for our records. They worked a Saturday, provided camera footage and a written summary, and did not disrupt any of our tenants. That is rare in this trade.
Google ★★★★★4.9
Two dogs and a house that was always dusty. They cleaned 14 runs and the blower wheel in about three hours. Two weeks later I am dusting once a week instead of every other day. Should have done this years ago.
PureBreeze Path has been cleaning ductwork in Murphy since 2022, and in that time we have worked on just about every system type this area has: 1990s sheet metal trunks in Murphy Village, flex-heavy retrofits in Country Ridge, and newer variable-speed installs in Stonebridge. Our technicians hold NADCA Air Systems Cleaning Specialist (ASCS) credentials and follow the NADCA assessment, cleaning, and verification standard on every job. We are EPA Lead-Safe certified, OSHA 10 trained, and carry IICRC certification for the moisture and mold side of the work.
Real answers to the questions we hear most often from local homeowners and property managers.
Local air duct cleaning means the crew that shows up actually works this area. We know the duct layouts in Murphy Village and the flex runs common in Country Ridge, so we bring the right brush sizes and whip heads on the first trip instead of guessing.
View local Airduct cleaningIf you are searching air duct cleaning near me, you want a company that can be at your door this week, not next month. We run routes through Murphy daily and keep openings for short-notice calls, including Saturdays when the schedule allows.
View Airduct cleaning near meSome duct problems cannot wait for business hours. Water intrusion after a storm, a duct that collapsed, or a system pushing visible debris into a nursery all justify a late call. We run 24/7 dispatch for these situations across Murphy and Collin County.
View 24/7 Airduct cleaningSame-day air duct cleaning is available when we have a slot open, and we hold a few each week for Murphy addresses. Call before noon and there is a good chance we can be there the same afternoon, inspection included.
View Same Day Airduct cleaningEmergency air duct cleaning covers the situations that cannot wait: mold growth in ductwork spreading after a leak, smoke odor after a kitchen fire, or a rodent infestation in the duct runs. We treat these as priority calls and dispatch accordingly.
View Emergency Airduct cleaningRestaurants, offices, and retail spaces in Murphy Marketplace need duct cleaning on a schedule that does not disrupt business. We work after hours and weekends, and we document the job with camera footage for your facilities records.
View commercial Airduct cleaningCall (855) 948-0345 or email info@purebreezepath.com and we will get back to you fast. Our phones are answered 24/7 for emergencies, and regular scheduling runs Monday through Friday, 8 a.m. to 6 p.m. If you are in Murphy, we can usually get a tech to your door the same day.
Phone
(855) 948-0345Address
410 W Farm to Market 544, Suite 102 Murphy, TX 75094 USA, Murphy, Texas
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
