Every Furnace cleaning Murphy TX job includes the full mechanical clean of the furnace cabinet and the connected ductwork, plus camera documentation before and after. We quote flat, and the price you hear on the phone is the price on the invoice. Add-ons like duct sanitizing or dryer vent cleaning are quoted separately if you want them.
We pull the blower assembly, wash the wheel and housing in coil cleaner, let it dry fully, and reinstall it balanced. A caked blower wheel is the number one cause of reduced airflow we see in Murphy homes, and cleaning it restores the system to its rated CFM.
We brush the heat exchanger surfaces and vacuum the burner compartment with a HEPA vacuum. Dust on the exchanger insulates the metal and drives up surface temperature, which shortens equipment life. This step is why furnace cleaning is not the same as duct cleaning alone.
Every supply and return run gets a rotary brush followed by an air whip, all under negative pressure from the negative air machine. Flexible duct gets gentler treatment than sheet metal duct so the liner stays intact. We clean 8 to 18 runs depending on the size of your Murphy home.
We run the duct camera through the trunk and several branch lines before and after cleaning, and you watch the monitor with us. You get the footage as proof of work. If the camera shows the ducts were already clean, we tell you and adjust the scope before we start.
We install a new HEPA filter sized to your system before we leave. A clean system with a dirty filter is a waste of money. If your filter housing is the wrong size for the system, we will tell you and note it on the invoice so you can correct it.
Any access panels we cut or open get sealed back up with mastic and duct sealant. Leaky access panels pull attic air into the system, which undoes the cleaning within a season. We seal every panel we touch so the system stays clean longer.
Furnace cleaning Murphy TX is the mechanical cleaning of the furnace cabinet, blower assembly, heat exchanger surfaces, and the connected supply and return ductwork that carries conditioned air through your home. We pull the blower, wash it in coil cleaner, wipe down the cabinet interior, and run a rotary brush and air whip through each branch line while a negative air machine holds the whole system under vacuum. A HEPA vacuum catches what the brush loosens. Nothing gets pushed into your bedrooms.
In Murphy, the furnace works harder than most homeowners realize. Collin County summers push the AC for five straight months, then the first cold snap in November flips the system to heat and every bit of dust, pet dander, and construction debris that settled in the ductwork gets cooked and recirculated. If you have been searching for Furnace cleaning Murphy TX near me because someone in the house wakes up congested every morning, that is usually the ductwork talking, not the pollen.
Five steps, one visit, and you see the camera footage before we pack up. Here is exactly what happens from the moment we pull into your driveway.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Negative air machine
Holds the entire duct system under negative pressure during cleaning so nothing we loosen escapes into the living space. We size the machine to the system volume, which matters on larger Murphy two-story homes.
HEPA vacuum
Captures fine particulate, pet dander, and drywall dust that the brush and air whip knock loose. HEPA filtration is what separates a real cleaning from a surface wipe-down.
Rotary brush and air whip
The rotary brush scrubs duct walls, and the air whip reaches into corners and bends the brush cannot. We use gentler settings on flexible duct than on sheet metal duct so the liner stays intact.
Duct camera
Lets us see inside the ductwork before and after cleaning, and lets you watch the footage with us. If a competitor cannot show you camera footage, they are guessing at what is in your ducts.
Duct fogger
Applies EPA-registered sanitizer as a fine mist that reaches the full duct interior after mechanical cleaning. We only fog after the ducts are clean, never as a substitute for cleaning.
Compressed air nozzle
Reaches tight spots around the heat exchanger and burner compartment where a brush will not fit. Used with the HEPA vacuum running to capture what it loosens.
Rotobrush and Nikro equipment
Our primary cleaning platforms. Both are maintained and calibrated on a quarterly schedule so the brushes and vacuums perform to spec on every Murphy job.
NADCA ACR standard
The NADCA ACR standard is the industry benchmark for air system cleaning, and we follow it on every job. It covers source removal, negative pressure, and verification. If a crew cannot tell you what standard they clean to, that is a red flag.
Source removal, not masking
We remove the dust, dander, and debris from the system rather than fogging over it or relying on filters to catch what is already stuck to the duct walls. Source removal is the only method that actually solves the problem.
Camera-verified before and after
Every job starts and ends with duct camera footage from the same lines. You see what was in the system and what is left. This is how we prove the work was done and how you know the cleaning was not a surface pass.
Access panel sealing with mastic
Any panel we open gets sealed back with mastic and duct sealant. Leaky access panels pull attic air into the system, which reintroduces dust and undoes the cleaning within a season. Sealing is part of the job, not an add-on.
01
What we do: We run the duct camera first to see what we are dealing with, then clean the furnace and ductwork to a known baseline. If the previous owner never cleaned the system, we usually find 5 to 10 years of dust in the trunk line. We document everything so you have a service record going forward.
→ You start ownership with a clean system, a camera record, and a clear maintenance schedule instead of guessing what the previous owner did.
02
What we do: We clean the furnace and ducts, install a fresh HEPA filter, and offer the air duct cleaning for allergies add-on with EPA-registered sanitizer. The camera scan tells us whether the ductwork is the source or whether the issue is elsewhere in the home.
→ Most Murphy families report less morning congestion within 7 to 10 days after the cleaning, especially when the ductwork had visible dust and dander buildup.
03
What we do: Post construction duct cleaning is a different scope than routine cleaning because drywall dust and insulation fibers settle into every branch run. We clean the furnace and all ductwork, then run the camera to confirm the fine particulate is gone before we close up.
→ The white dust stops reappearing on furniture, and the HVAC system stops pulling construction debris through the blower every cycle.
04
What we do: We inspect the affected duct runs first with the camera, identify any mold growth in ductwork, and treat it with sanitizer after mechanical cleaning. If the duct insulation is saturated, we flag it for replacement rather than cleaning over a wet section.
→ The odor is gone, the mold is treated, and you have camera documentation showing the duct interior is clean before the next cooling season.
Murphy sits in Collin County with a climate that punishes ductwork in two directions. Summer humidity sits above 60 percent for months, which is when we see most of the mold growth in ductwork calls come in, especially on flexible duct runs in attics. Then the first cold snap in November flips the system to heat and every bit of dust that settled over the summer gets cooked and recirculated. The housing stock matters too. Homes built before 2000 in Murphy Village and Downtown Murphy tend to have sheet metal duct with more joints and more opportunities for leaks, while newer builds in The Reserve and Stonebridge have tighter systems that still collect construction dust for the first few years. We size our equipment and adjust our brush settings to the duct material we find, and we run heater cleaning Murphy 75094 calls with the same camera-verified process whether the home is 1,400 sq ft or 4,000.
Maxwell Creek
Mix of 1990s and 2000s builds with mostly sheet metal duct. We see more joint leaks here than in newer neighborhoods, and we flag them on the invoice so homeowners can get them sealed.
The Reserve
Newer construction with tight, well-sealed duct systems. The main issue here is construction dust still sitting in the trunk line for the first 2 to 3 years after the build.
Willow Wood
Established neighborhood with mature trees, which means more attic debris and occasional rodent activity in duct runs. We check for pest intrusion on every job here.
Murphy Village
Older single-story homes with original ductwork in many cases. We see more flexible duct replacements needed here, and we are EPA Lead-Safe certified for the pre-1978 paint.
Parker Road Corridor
Mix of residential and commercial properties. We run both residential and commercial air duct cleaning calls along this corridor, often on the same day.
High summer humidity driving attic duct condensation
Flexible duct runs in Murphy attics sweat in July and August, which is the leading cause of mold growth in ductwork we find. We check moisture levels before cleaning and treat affected sections rather than cleaning over a wet surface.
First cold snap pulling settled dust into the airstream
The November switch from cooling to heating is when most Murphy homeowners notice the dust and smell. That is the dust that settled in the ductwork over the summer getting cooked and recirculated. Cleaning before the switch prevents the problem.
New construction dust in recently built homes
Murphy has added a lot of new housing in the last 5 years. Drywall dust and insulation fibers settle into every branch run during the build and get blown through the house for months. Post construction duct cleaning solves it in one visit.
Pet ownership rates above the national average
Murphy is a pet-heavy city, and pet dander binds to duct walls and holds other debris in place. We run the rotary brush and air whip specifically to break that bond, then HEPA vacuum the loosened dander out of the system.
These are the four calls we get most often from Murphy homeowners, and what is usually going on when we arrive.
Problem
Dust on every surface within a day of cleaning, and allergy flare-ups that never seem to go away no matter what filter you buy.
Our Fix
We clean the furnace cabinet, blower, and every branch run under negative pressure so the dust source is removed, not just filtered. Then we seal the access panels with mastic so attic dust stops getting pulled into the system. Most Murphy customers see the visible dust drop within a week.
Problem
A persistent odor that makes the whole house feel damp, and a strong signal that mold growth in ductwork is active somewhere in the system.
Our Fix
We run the duct camera to locate the mold, identify the moisture source, treat the affected sections with an EPA-registered sanitizer via duct fogger, and verify with the camera before closing up. If the moisture source is a duct leak in the attic, we flag it so you can get it sealed.
Problem
The furnace runs longer to hit the setpoint because the blower wheel and heat exchanger are coated in dust, and the system works harder for the same result.
Our Fix
Cleaning the blower wheel and heat exchanger restores airflow and lets the system short-cycle less. Murphy customers on 2,000 sq ft homes commonly see runtime drop by 10 to 15 percent after a full cleaning. That shows up on the next utility bill.
Problem
Dander binds to duct walls and holds other debris in place, so the system keeps recirculating the same allergens every time the blower runs.
Our Fix
The rotary brush and air whip break the bond between dander and duct wall, and the HEPA vacuum captures it instead of pushing it into the living space. We also install a fresh HEPA filter sized to the system. Most pet owners in Murphy notice the difference within a week.
Four outcomes our Murphy customers notice within the first week after we clean the furnace and ductwork.
Noticeably cleaner indoor air
A furnace cabinet packed with dust blows that dust into every room every time the blower kicks on. After we clean the cabinet and seal the access panels, most Murphy families report less visible dust on furniture within 5 to 7 days. If allergies are the driver, ask about our air duct cleaning for allergies add-on.
Lower heating bills
A dirty blower wheel moves less air, so the furnace runs longer to hit the thermostat setpoint. Cleaning the wheel and the return plenum restores airflow and lets the system short-cycle less. Murphy customers on 2,000 sq ft homes commonly see the runtime drop by 10 to 15 percent after a full cleaning.
Fewer musty odors
Musty odors coming from the vents usually mean mold growth in ductwork, especially on the flexible duct runs in attics where Murphy humidity sits above 60 percent most of the summer. We treat affected sections with a duct fogger and EPA-registered sanitizer, then verify with the duct camera before we close up.
Longer equipment life
Dust on the heat exchanger insulates the metal and drives up surface temperature, which is the leading cause of cracked exchangers we see in Murphy homes built before 2010. Cleaning the exchanger and the blower every 3 to 5 years keeps the furnace running to its rated service life instead of failing at year 12.
Google ★★★★★4.9
PureBreeze Path cleaned our furnace and ducts in Maxwell Creek last month. They showed us the camera footage before and after, which no other company even offered. The dust on our furniture dropped noticeably within a week. Fair price, on time, and they sealed the access panels properly.
Yelp ★★★★★5.0
Called about a musty smell in our Willow Wood home and they had a crew out the same day. Found mold on two attic duct runs, treated it, and showed us the after footage before they left. The smell was gone in two days. Honest pricing and no upsell.
BBB ★★★★★4.8
We used PureBreeze Path for post-construction duct cleaning after a kitchen remodel in The Reserve. They got all the drywall dust out of the system and cleaned the AC coil while they were at it. The white dust stopped coming back within three days. Would use them again.
Google ★★★★★4.9
Best experience we have had with an HVAC-related service in Murphy. They pulled the blower, cleaned the heat exchanger, and ran the camera through every branch line. Showed us the footage at the end. Our heating bill dropped about 12 percent the next month. Highly recommend.
PureBreeze Path has been cleaning furnaces and ductwork in Murphy since 2022. In that time we have worked on everything from 1980s single-story ranches in Murphy Village to new builds in The Reserve with tight, well-sealed duct systems that still collect construction dust. Our technicians hold NADCA Air Systems Cleaning Specialist (ASCS) credentials and OSHA 10 cards, and we follow the NADCA ACR standard on every job. We are also EPA Lead-Safe certified, which matters on the older homes around Downtown Murphy where pre-1978 paint is still in play. We do not subcontract. The crew that shows up is the crew that cleans.
Real answers to the questions we hear most often from local homeowners and property managers.
Local air duct cleaning is the natural companion to furnace cleaning in Murphy. When we pull the blower and clean the cabinet, we are already set up on the trunk line. Adding the full duct system to the same visit saves you a second trip charge and gets the whole system clean in one pass.
View local Airduct cleaningIf you searched air duct cleaning near me and landed here, you are in the right place. We cover every Murphy neighborhood from Murphy Marketplace to Stonebridge. One call books both the furnace cleaning and the duct cleaning, and we handle the whole system in a single visit.
View Airduct cleaning near meOur 24/7 air duct cleaning dispatch covers Murphy for post-storm calls, water intrusion events, and real estate closings that need the system clean before the walkthrough. If your furnace took on water or you smell something musty after a summer storm, call and we will get a crew out.
View 24/7 Airduct cleaningSame day air duct cleaning is available most weekdays if you call before noon. Murphy homeowners use this for last-minute showings, guest arrivals, and the day the new puppy comes home. We keep two slots open daily for same-day calls in Collin County.
View Same Day Airduct cleaningEmergency air duct cleaning is for the situations that cannot wait: mold growth in ductwork discovered during a repair, smoke odor after a kitchen fire, or a furnace that pulled in debris from a roof leak. We run emergency dispatch across Murphy and can usually be on site within a few hours.
View Emergency Airduct cleaningCommercial air duct cleaning for Murphy offices, retail spaces, and restaurants along the Parker Road Corridor runs on the same equipment we use in homes, scaled up. We schedule after-hours so your business does not lose a day of operation.
View commercial Airduct cleaningCall (855) 948-0345 or email info@purebreezepath.com and we will get back to you fast. Our phones are answered 24/7 for emergencies, and regular scheduling runs Monday through Friday, 8 a.m. to 6 p.m. If you are in Murphy, we can usually get a tech to your door the same day.
Phone
(855) 948-0345Address
410 W Farm to Market 544, Suite 102 Murphy, TX 75094 USA, Murphy, Texas
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
